The plastics processing industry, a good development prospects, and will continue to be the main driving force of the rapid development of China’s press industry. To the development of China’s plastics machinery industry after WTO entry, at least have two favorable premise: First, is conducive to the introduction of technology; is conducive to export, including the improvement of foreign businesses and joint ventures and enterprises run older generation manufacturing technology.

China’s plastics machinery has become one of the fastest growing industries in the traditional machinery manufacturing, the annual demand increase. The rapid development of China’s plastics machinery industry due to the following factors: First, the elimination of the demand for high-tech equipment, equipment updates and obsolete equipment; two is at home and the rapid development of the plastics processing industry, demand for plastic machinery. Resource utilization plastic recycling, plastic recycle machine, plastic shredder has played an inreplaceable role.

Increasingly pursuing economic development, environmental protection may be some people to play down, forgotten. Some people say that plastic products are not environmentally friendly. Why not to a certain extent to achieve a “win-win”? Plastic recycling equipment can greatly reduce the unreasonable waste of resources and environmental pollution. I believe that when the plastic bring us not only a convenient, it is an environmentally friendly concept of savings.

One reason, from the output of waste plastics Angle:

Along with the plastic products continuously increasing consumption, waste plastic also grow. At present our country waste plastic mainly for the plastic film, plastic wire and weaving, foam plastics, plastic packing boxes and containers, daily plastic products, plastic bags and agricultural film, etc. In addition, China automobile use plastic years consumption has more than 400000 tons, electronic appliances and electronics kit with the plastic years consumption has more than 1 million tons, the product is disposed became an important source of waste plastics. China plastics processing, chairman of the association LiaoZhengPin once pointed out that by 2015 to 15 million t reduced, recovery rate reached 30%.

Reason # 2, from the perspective of waste plastics market price:

The market price of the lower recycle plastic aggregates have obvious needs. Due to recycle plastic in price and new materials compared with obvious advantage, general price only new material 1/2 to two-thirds, or even lower, so in some recycled material can meet the requirements of the field, recycle plastic processing from the aggregates became the first choice of these manufacturer. In addition, the country out of effective use resources, protecting the environment on the purpose for resource recycling, especially plastic recycling energetically advocate, and introduced a number of related incentives, such as: plastic shredder manufacturing enterprise, plastic bottles compressed package manufacturing enterprise, plastic blow molding enterprise, plastic recycling equipment enterprise already get state relevant policies to support.

Reason # 3, and from the waste plastics finally has the market value analysis:

At present, China’s market value of waste plastic application is in 100 billion yuan of above. In recent years, plastic raw material prices for the market has greatly promoted role, waste plastic prices also rose sharply, among the more pure polyethylene, polypropylene recycling materials of the highest price to 6000 multivariate/tons, close to the price of raw materials rose not before.

Therefore, our country recycle plastic aggregates production increase in successive years. Along with the national environmental protection efforts strengthened day by day, waste plastic recycling industry development prospects will is broader, plastic recycling equipment also get more QiYeZhe plastic the pro-gaze.

Plastic Granulator Machine operation involving the national economy in the field, plastic Granulator Machine andPlastic Shredder machine is as China’s Plastic Recycling Machinery of large energy consumption, in addition to plastic recycling the pollution caused by the process and is often an important source of China’s environmental pollution, plastic recycling the progress of technology with the entire national economy national economy development have very close relationship. Plastic recycling the main fabrics predicament has:

1: plastic recycling operation involving the national economy in the field, plastic agglomerating manufacturer is China’s large energy consumption, in addition to plastic recycling the pollution caused by the process and is often an important source of China’s environmental pollution, plastic recycling the progress of technology with the entire national economy national economy development have very close relationship.

2: recycling material pollution to the environment is quite serious. The most widely used in all kinds of conventional plastic recycling equipment, more than three-quarters of hot air is plastic recycling, this kind of plastic recycling equipment to the environment pollution is very serious, plastic recycling system for coal of reform of the furnace has become an important issue to be solved.

In the exploration of the new technology of plastic recycling road to development, energy efficiency, environmental protection and must be considered the quality of the product, in order to achieve the comprehensive, coordinated and sustainable development. To implement efficient and green plastic recycling development strategy, first to go resource saving development path, become a single extensive plastic recycling for combination, intelligent plastic recycling. Not only from plastic recycling process on the fundamental transformation, but also makes a comprehensive and multi-level energy-saving technical renovation, develop renewable energy and industrial application of waste heat of plastic recycling technology.

With international and domestic plastics raw materials market fluctuations, renewable plastic market demand present situation, waste plastics import also shows ascendant trend, and with plastic recycle machine also had a good development, such as plastic shredder, plastic recycling, plastic recycling machine, etc.

The Chinese market at present for plastic market demand, still far greater than domestic production. At present, the manufacturer to cut costs and the improvement of environmental protection consciousness, have turned to buy recycled plastic. Transportation and electric appliances, electronic production enterprise in its products by 25% ~ 30% recycled plastic. And as the international and domestic plastics raw materials market fluctuations, renewable plastic market demand present situation, waste plastics import also increase.

The relevant departments of the state was announced, our country each year about 14 million tons of waste plastic didn’t get recycling, renewable utilization rate is only 25%. With this news release, a huge regeneration product market have been emerging.

At present, the zhejiang province taizhou region of waste plastic accounted for 10% of the country’s demand for a year, plastic consumption of 4 million tons, but which the consumption of waste reached 1 million tons, some enterprises more than new material consumption quantity. And waste plastic recycling equipment in addition to solve ecological environment and reutilized and beam is an important way to outside, is more can not use digital measure industrial information and potential business opportunities.

Since the synthetic tree skeleton successfully since industrialized production, and people’s life, the production, the scientific research each field has changed a lot. Can say, no synthetic resin industry, many modern industrial became like. First, resin as the main raw material form of the bag of color image plastic products into the dry home all households, the rich, the beautification on people’s life. As long as when we looked around, almost everywhere you can find many synthetic materials products, such as chimney, clocks, in form, juice count machine, refrigerators, washing machines, advocate tone, shell, the kitchen supplies, things that defend bath, office supplies, toys are all made of plastics to form. In the industrial fields, and plastic products with its excellent characteristics successfully used in packing industry, construction, communication, electrical and electronic engineering, medical equipment, chemical equipment, transportation factory and space and a Marine development, and other fields. In agriculture, plastic film, woven bags, etc most used plastic products.                                 In scientific research field, and constantly development of high-performance synthetic materials for the development of high and new technology to provide more and more effective structure, functional materials, and are instead of traditional metal, ceramic and other materials, widely used in the high-tech frontier. Visible, plastic products has become the modern industry and everyday life indispensable important material. The wide application of natural also took up the plastic machinery in the innovation and development. Over the years, “under the concept of environmental protection in, plastic recycling also became an important issue. plastic recycling machinery , plastic shredder, and a series of plastic recycling equipment also more and more attention by people with well known. For the plastic recycling ZhiHui not city a benefits the country and of good matter, want more people to join. For our life together.

Plastic is widely used in civil, industry, agriculture and other areas, but it also brings "white pollution", etc. Now, the country is very attached great importance to environmental protection and utilization of renewable resources, plastic industry sustainable development is extensive concern of the whole society. Plastic if can get very good development recycle, will be a benefits the country and the big and good matter, and is also a good reutilized industriy project, so plastic recycling machinery is a great project.
At present,plastic products in China has a huge potential for development, plastic application field is expanding, and people’s life of related to eat, wear, live, are all closely related with plastic, has become part of everyday life, can say to all the places where there are people can see plastic, plastic products industry is the root of waste plastic and consumer market of waste plastic, plastic recycling machinery has broad prospects, can eliminate the white pollution, also can save the energy and keep the ecological balance, and realizing the resources use positive cycle, reuse, which benefits the country and, thus plastic granulator is never out of the industry.
In recent years, China’s GDP growth speed quickly, but painfully, this and predatory development of resources become direct ratio. In fact, plastic regeneration utilization rate is not high, industry technical level development is slow. Therefore, the country attaches great importance to the resource recycling.

Plastic crusher is plastic recycling machine and it can reuse, can create more useful to production material, here is to introduce the use of plastic crusher.

1, before we start, should use first human will move driving wheel engages a two laps, confirm flexible motion activated after boot. And only after working normally crusher for material. Motive power supply power. The parts for damage. 2, stop before operation, should first stop feeding and will machine material row net, and then cut

3, in the works to pay attention in the temperature of the bearing, ensure bearing keep good lubrication condition, and

Note sound and vibration without exception. Found not normally, should stop check whether was not broken objects gets stuck, or 4, to keep the crusher of feeding even, prevent overload. Defend metal and wood can’t be broken objects fall into the machine. Can’t broken, enters the material moisture too much; Wet broken, it needs to maintain proper water, due to the strong water shortage and congestion, reduce the production ability. And take the appropriate measures to eliminate. 5, check whether the granularity of broken product meets the requirement. If the size of the particle too much more than the required, should find out the reasons (such as screen flaw is too large, discharging mouth wide, hammer wear and so on), 6, crusher parking, check whether the bolt firm, easy to wear parts of the 7, grinding how wear degree. Tooth crusher, it should also use parking opportunity caught in the teeth away between of the wood. The loss of the parts, should change in time or repair. Save trouble, and make insurance device failure. FHG series plastic crusher when using note:

8, crusher insurance device, must keep a good state, must not be for 1, FHG series

Plastic crusher and power units to installation is firm. If need to plastic crusher long-term fixed assignments, should its fixed in cement base on the development; If need to plastic crusher work flow, the unit should be installed in the seat made with Angle iron, and ensure that power machine (wood oil machine or motor) and plastic crusher sheave turning on the same plane. Is suitable or not. 2, FHG series plastic broken machine after installation to check all the tighten fasteners, if there is a loose to give to screw. At the same time to check the tightness of rewinding 3, FHG belt series plastic crushers before starting, with the hand first rotating rotor, check the tooth and claw, hammer of rotor operation is flexible and reliable, the broken indoor have collision phenomenon, the direction of rotation and whether the rotor machine arrow direction, power and plastic crusher lubrication is good or not. 4, don’t literally change pulley, in case the speed is too high, plastic crushers 5 after starts should keep that room have broken explosion, or low speed crusher work efficiency of influence. Its first idling 2 ~ 3 min, no abnormal phenomenon feed again after work.

6, work must always be plastic crusher operation situation, first, feed uniformly, in case of obstruction broken material room; Second, don’t long time overload. If you find that there is the vibration and noise, bearing and the body temperature is too high, the phenomenon such as material to spray, shall be immediately stop check and remove the faults rear can the renewal work. Note 1, before we start, should use first human will move driving wheel engages a two laps, confirm flexible motion activated after boot. The broken machines such as operating normally before feeding. 2, stop before operation, should first stop feeding and will machine material row net, and then cut motive power supply power. 3, in the works to pay attention in the temperature of the bearing, ensure bearing keep good lubrication condition, and pay attention to sound and vibration without exception. Found not normally, should stop check whether was not broken objects gets stuck, or parts for damage. 4, to keep the crusher of feeding even, prevent overload. Defend metal and wood can’t be broken objects fall into the machine. Can’t broken, enters the material moisture too much; Wet broken, it needs to maintain proper water, due to the strong water shortage and congestion, reduce the production ability. 5, check whether the granularity of broken product meets the requirement. If the size of the particle too much more than the required, should find out the reasons (such as screen flaw is too large, discharging mouth wide, hammer wear, etc), and take proper measures to eliminate. 6, crusher parking, check whether the bolt firm, easy to wear parts of how wear degree. Tooth crusher, it should also use parking opportunity caught in the teeth away between of the wood. 7, grinding the components of the loss, should change in time or repair. 8, crusher insurance device, must keep a good state, must not be for save trouble, and make insurance device failure. FHG series plastic crusher when using note: 1, FHG series plastic crusher and power units to installation is firm. If need to plastic crusher long-term fixed assignments, should its fixed in cement base on the development; If need to plastic crusher work flow, the unit should be installed in the seat made with Angle iron, and ensure that power machine (wood oil machine or motor) and plastic crusher sheave turning on the same plane. 2, FHG series plastic broken machine after installation to check all the tighten fasteners, if there is a loose to give to screw. At the same time to check the tightness of rewinding belt is appropriate. 3, FHG series plastic crushers before starting, with the hand first rotating rotor, check the tooth and claw, hammer of rotor operation is flexible and reliable, the broken indoor have collision phenomenon, the direction of rotation and whether the rotor machine arrow direction, power and plastic crusher lubrication is good or not. 4, don’t literally change pulley, in case the speed is too high to break room produce explosion, or low speed crusher work efficiency of influence. 5, plastic crushers after starting should keep its first idling 2 ~ 3 min, no abnormal phenomenon feed again after work. 6, work must always be plastic crusher operation situation, first, feed uniformly, in case of obstruction broken material room; Second, don’t long time overload. If you find that there is the vibration and noise, bearing and the body temperature is too high, the phenomenon such as material to spray, shall be immediately stop check and remove the faults rear can the renewal work.

Plastic recycling equipment and plastic Shredder is really solve the appear in production of waste plastics a big problem, but for the use of machinery must be properly, so that the life of the machine will be more long.

Asia-pacific, South America and central and eastern Europe of the developing countries will present higher growth of PET packing, this will lead to the growing real income and traditional packaging form by PET bottle instead. The asia-pacific region in 2007-12 period beyond North America and Western Europe has become the largest PET packing regional market. The asia-pacific region of the world is 2012 PET packing consumption of 29.4%, the second is 24.1% and 19.7% in North America and Western Europe. Because of the growing for PET bottle of the impact on the environment of the consumer attention, for PET supply chain for the merchants of PET recovery is another key issue. PET recovery needs corresponding recycling industry chain keep up with, from plastic Shredder, plastic granulator to PET recycling machine. PET recycling function recovery PET materials saving fossil fuel, lower energy consumption, so as to reduce greenhouse gas emissions.

Legislation and resources protection scheme is PET development and recycling of the main driving force. Recovery of PET (rPET) market growth from those in order to make his own brand in the environment and the economy highlight the real differences and signed global brand recycled PET owners push.

As rPET use, the rise of the products in the rPET composition for the bottle is popularity still exist some uncertainty. The bottle components of the rPET composition intake will depend largely on whether rPET cost than the original material low. In addition, although renewable PET strong demand, but still exists the raw material supply and infrastructure can’t expanded rapidly enough to collect the industry needs of materials of the problem. And some worry is that supply quality can rPET industry in negative effects.

By 2017, the key technology development is also included in the further development of the cut off system, light, and the share of continue to study and pay more and more attention to sustainable development and recycling. PET production process of compression technology is another kind of new development.

The current recovery slice reengineering plastic bottle technology of PET bottle is mature, many plastic recycling machinery also got the corresponding development, such as plastic recycling machine, PET recycling machine and so on,many of the enterprise has the related production line in the production. But, the chaoyang environmental protection industry is the biggest problems facing the raw materials of waste plastics bottle of shortage. Why will appear this kind of circumstance?

First of all, the garbage classification recycling meaning not thorough popular feeling, the lack of public recycling concept. A large number of plastic bottles and bottles of standard, cover and other recyclables adhesion. This makes a cost recovery, will need a lot of money used for sorting PET bottle. Secondly. Plastic recycling market good and evil people mixed up, from gleans half the family to the user to the individual practitioners to large recycling garbage collection field, the whole chain each link hard integrate effectively, the source is not stable, not easy for mass production. Again, textile and other enterprise in the competition for markets, textile materials have part of waste plastics bottle of recovery from the market, this makes the recovery intense market competition.

For the present this situation, on the one hand, the government departments concerned should set up as soon as possible waste classification recycling feasible channel. On the other hand, the enterprise also to open its own establishment relevant collection points, to meet the production requirements.

Plastic rubber machinery equipment and Italian mould manufacturer’s industry association Assocomaplast said, first quarter 2012 Italian plastic and rubber processing machinery import and export continue to present a positive trend, with overseas sales up 17% compared to the same period in 2011.

According to the statistics institutions of the Italian ISTA data, this rise up a Plastic Shredder andPlastic Recycling Machine “gentle slowdown”, and the mold and Pet Recycling Machine export prospects also more optimistic. Assocomaplast on July 3′s statement, the mould and extrusion machine by purchasing activities of the drive, the industry has also appeared in import growth of 22%.

Italian plastic and rubber machine exports the main DuiXiangGuo, Germany appear “considerable growth” (19%), close to 90 million euros sales, accounting for two-thirds of the mould export. Instead, China’s sales were down 19%, ranking third fell to about 34 million euros. France sales growth of 37%, in the number two. In other countries, the United States increased by 34%, and a 30% growth in Poland, Brazil increased by 28%, and Turkey growth of 17%.

Active resin with machinery, import declined slightly to 203000 euros, while exports grow 3% to 8.1 million euros. Foam material to use machinery import basic did not change (865000 euros), and exports have dropped 5% to 4.9 million euros.

Environmental protection concept raids compound wood prospects but period

As a saving of the new materials and wood, after more than 10 years of independent development, compound wood is gradually developed into a new industry. Especially in energy conservation and emission reduction in increasingly strengthen, the circular economy development momentum is the strength of “1025″ period, has the raw material resources and products can be plasticizing, environmental protection renewable, etc of the advantages of the compound wood industry and adapted to the sustainable development of the trend, highlights the growing development potential.